Participant 1
Initial description: to match the pattern starting with the top left sqaure in the 4 corner squares
Final description: to match the pattern starting with the top left sqaure in the 4 corner squares
Participant 2
Initial description: Not sure what the point of this was either. Perhaps to close the gap on the mask.
Final description: Once again, not too entirely the significance of this was.
Participant 3
Initial description: Beginning with the top left part of the colored grid, use the pattern from left top to the middle top as far as four grid squares down.
Final description: Beginning with the top left part of the colored grid, use the pattern from left top to the middle top as far as four grid squares down.
Participant 4
Initial description: Create a pattern by using the top outer portion that makes a square of the test input.
Final description: Create a pattern by using the top outer portion that makes a square of the test input.
Participant 5
Initial description: It was to take a corner of the input and zoom in on it
Final description: It was to take a corner of the input and zoom in on it
Participant 6
Initial description: The upper left quadrant of the input design is reproduced in the output.
Final description: The upper left quarter of the symmetrical design in the input grid is reproduced in the output grid.
Participant 7
Initial description: Create a colorful pattern by alternating between all the colors in the demonstration.
Final description: i was trying to fill in all the colors in the task
Participant 8
Initial description: Recreate the sample input by zooming in on the corner
Final description: Recreate the sample input by zooming in on the corner
Participant 9
Initial description: The top left corner was repeated
Final description: The top left corner was repeated
Participant 10
Initial description: Make the grid smaller to a 4x4 and copy the pattern from the larger grid and put it in the smaller grid making it show only part of the pattern.
Final description: I took the pattern copied the pattern from the original grid starting with just the blue color corners then pasted it into a 4x4 grid.
Participant 11
Initial description: Create a grid pattern by copying the 1st 4x4 square in the example input.
Final description: To create the test output grid pattern, find the center square of the test input pattern. It will be a 2x2 square. Starting from the top left square, go up 4 and over to the left 4, down 4, and back over to the right 4. Copy the 4x4 pattern shown in the test output.
Participant 12
Initial description: One quarter of the design.
Final description: One quarter of the design.
Participant 13
Initial description: Extract one quadrant of a symmetrical pattern
Final description: Extract one quadrant of a symmetrical pattern
Participant 14
Initial description: cut the shape into 4ths on a 4x4 grid
Final description: cut the shape into 4ths on a 4x4 grid
Participant 15
Initial description: Recreate the upper leftmost quadrant of the pattern.
Final description: Recreate the upper leftmost quadrant of the pattern.
Participant 16
Initial description: Starting from the top left center square build out the picture wiht the remaining spaces.
Final description: Starting from the top left center square build out the picture wiht the remaining spaces.
Participant 17
Initial description: Create a 4x4 grid. Place a gray block on the top left and one below it. Then place two gray blocks next to each other in the row below. After that, place two green blocks in the top right half of the grid and one blue block in the bottom right square. Finally, put two red blocks at the bottom left.
Final description: Place one gray block at the top-right most position. Then, add three gray blocks on the second row, in the three right-most positions. Add two green blocks on the third row, in the right-most positions. Place one gray block as the second-to-last block in the third row. Next, add two red blocks on the fourth row, and one green block as the third block in the fourth row. Finally, add one light blue block at the end of the fourth row.
Participant 18
Initial description: Place the upper left 5x5 portion of the test input into the test output.
Final description: Place the upper left 5x5 portion of the test input into the test output.
Participant 19
Initial description: Cut out the upper left quadrant of the rotated pattern
Final description: Cut out the upper left quadrant of the shape and remove any extra surrounding black rows/columns
